Cybelec V-DNC-63-P8

[simplextibi 0]

Hi all

 

Does someone have a existing machine wirring diagram for this controller and rest of CNC press brake?

I have a Beyeler small 50 ton press brake with Y1-Y2 and rear back guage

Machine i purchased but wirring is done so i need to see a machine how it is wired safty and everything

I have a Cybelec MSV-402 controller in it for the controlling of pressure of Y1-Y2

 

thank you for the help

[vad0000 396]

11 час назад, simplextibi сказал:

Does someone have a existing machine wirring diagram for this controller and rest of CNC press brake?

I have INPUT/OUTPUT manual.

LS60-PS-0.pdf

[simplextibi 0]

Hello

Thank you i have this, i would like to see a example of a existing machines wirring

I have a problem of the RAM not moving at all, i dont know where to start :(

Maybe even paramter is not correct and maybe other stuff

I someone have a Cybelec technical instaructions, supposedly it has example working

 

thanks

Изменено 7 января 2020 пользователем simplextibi

[vad0000 396]

 

1 час назад, simplextibi сказал:

I have a problem of the RAM not moving at all, i dont know where to start

I need the photos of the buttons and the posiotion keys.

[simplextibi 0]

Ok

I w am uploading complete photos

Photos are to big so i created a zip

 

www.geobuild.hu/cybelec.zip

 

IMG_7847.jfif

[vad0000 396]

1. You have to enter BEAM parameters

2. You have X axis, or X1 and X2 axes?

3. I need also the photo of the electrical cabinet door?

 

[simplextibi 0]

Yes i have axis X1 X2 there is a proportional valve on top which keeps it in synchron

IMG_7895.jfif

IMG_7897.jfif

[vad0000 396]

38 минут назад, simplextibi сказал:

Yes i have axis X1 X2 there is a proportional valve on top which keeps it in synchron

You have mistaken, Y1 and Y2 are hydraulic axes.

X1 and X2 are mechanical axes. What induction motors do you have?

 

And I need the photo with positions switch.

[simplextibi 0]

ahhh

The axis are hydraulic with a proportional valve HVM-090-100 for ech one, each side has a Heidenhein sliding measuring.

I have a X axis in the rear with a rotary encoder and a 3PH motor

The hydraulic pump has a valve i gues to swith on the pressure with a manually adjustable pressure

The first problem i see is that on J9 i do not get the -/+10v outputs to controll the Cybelec MCV-402A

proportional valve controller, if i inducxe manually 10V it will give output, so i think the controller is nmot giving signal on J9

At the moment i dont care about rear just the Y1 and Y2

1.jfif

2.jfif

[vad0000 396]

13 минуты назад, simplextibi сказал:

I have a X axis in the rear with a rotary encoder and a 3PH motor

If You have only one X axis, why we have two X axes in machine parameters?

[simplextibi 0]

Ok, so parameter is bad

So how do i enter Y1 and Y2 axes?

On J12, J13 i have the linear mesuring encoder for Y1 and Y2

Изменено 8 января 2020 пользователем simplextibi

[vad0000 396]

You need no to enter the hydraulic axes, only mechanical.

You must enter all BEAM, PRESSURE and CALIBRATION parameters.

[simplextibi 0]

Ok so i change axis 0 to X nad erase all other

Can i use other 3 axis for R and other backgage axis?

What parameter controlls the J9 output for the MCV 402A controller?

 

[vad0000 396]

This controller can control up to two mechanical axes.

X; X and R; X and Z; X1 and X2.

[simplextibi 0]

I see you have experience with this

Can you help me configure the parameters step by step, page by page

I could pay for your help if you dont ask too much:)

I bought this machine and would like to get it in operation

[vad0000 396]

5 часов назад, simplextibi сказал:

Can you help me configure the parameters step by step, page by page

OK.

At first we enter machine parameters for mechanical axes.

Read this manual.

See the example on pages 51-52.

 

N2X7E.pdf

[simplextibi 0]

Hello

I configured the axis to 0 type

[vad0000 396]

2 минуты назад, simplextibi сказал:

I configured the axis to 0 type

You have servo axis or AC axis?

 

If you have AC axis, 120 patameter = 3

[simplextibi 0]

I have axis controller MSV402

I dont know if this is AC or DC controller

on manual you sent

axis parameter for P00

it says 0 for DC

1 for AC

3 for not controlled

 

Изменено 13 января 2020 пользователем simplextibi

[vad0000 396]

15 минут назад, simplextibi сказал:

I have axis controller MSV402

MSV402 is the hydraulic amplifier.

 

I need the photo of the motor. 

MSV402.pdf