dnc 80 cybeelec

[abdushibi 0]

i have problem with dnc 80 cybelec

in the upper right corner it says (DPRAM: NO ENC SIGNATURE) and if i press AUTO / AUTO-SEMI / MANUAL.

there notification (ENC NOT CONNECTED) what is problem r and what is the solution

 

https://fil.email/vg60Vi8E

[vad0000 396]

I need the photo of WELCOME page.

[abdushibi 0]

[vad0000 396]

However the massage ENC NOT CONNECTED will appear and it will not
be possible to work with the machine.
To reactivate the INTERNAL machine peripheral, you must:
- Select MACHINE INTERNAL.
- Initialize the ENC by pressing INIT ENC, Action menu.

[abdushibi 0]

thank you for reply
As a result of the delay in a reply from me .A problem has been resolved of  (DPRAM: NO ENC SIGNATURE) 
But I have another problem,after complete indexing,there is no displacement on the upper table when the pedal is pressed

also the key number 3 when i turns to position 3 is not working (I can't change anything).

[vad0000 396]

21 минуту назад, abdushibi сказал:

also the key number 3 when i turns to position 3 is not working

 

This key?

[abdushibi 0]

yes this key

[abdushibi 0]

[vad0000 396]

4 часа назад, abdushibi сказал:

yes this key

Check this key on the TESTS page.

[Tad 195]

6 часов назад, abdushibi сказал:

A problem has been resolved of  (DPRAM: NO ENC SIGNATURE) 

How was this problem solved?

[abdushibi 0]

I checked the key on the tests page and i found the following

when the key in postion 1 (see pic 1), on the tests page,  is zero see pic 2

 

when the key in postion 2 (see pic 3), on the tests page,  is 2 see pic 4

 

 

when the key in postion 3 (see pic 5 ), on the tests page,  is 2 see pic 6

[vad0000 396]

There are 4 wires 0 (common), 1, 2 and 3.

 

1. 0 + 1 = 1 position

2. 0 + 2 = 2 position

3. 0 + 3  and 1 + 2 = 3 position

 

You have no 1 and 3 position.

So I think, that there is the problem with the 1-st wire.

[abdushibi 0]

In your opinion, what is the solution to this problem?
 
 

[vad0000 396]

41 минуту назад, abdushibi сказал:

In your opinion, what is the solution to this problem?

I think, that you have to dismount the front panel and check the 1-st wire. 

[abdushibi 0]

i did ,there are four wires As you said i tested with avometer 

are ok  when i turn key to postilion 1  there contact between wire 0 and 1

also   between 0 and 2  also between 0 and 3

i mean also when i turn key to psition  2 there contact between 0 and 2 also when turn  to pisition 3

[abdushibi 0]

0+1 i see in tests page 1

0+2 i see in tests page 2

0+3 i se in tests page 0

[vad0000 396]

8 часов назад, abdushibi сказал:

0+3 i se in tests page 0

0+3 and 1+2 simultaneously - ?

[abdushibi 0]

what will be do to solve this problem i need position 3.

[vad0000 396]

33 минуты назад, abdushibi сказал:

what will be do to solve this problem i need position 3.

You have to use the different connection between the wires to find psition 3.

[abdushibi 0]

i did all connection but i did not get position 3, what will be do.