Пользование серво гайдом

[andrey2147 172]

предлагаю обсуждать пользование прогой,сам пока читаю мануал.

вопрос первый : как я понял из мануала можно подключить его через имеющийся LAN штеккер?

            второй: под семёркой работает или ХР виртуальной?

 

моя задача стартапить станки из кетая.

[bfi 101]

1. Через embedded ethernet работает на 0i-D, 30i/31i/32i/35i и А и Б версии. Работает и через Fast Etherned/Data Server board. PCMCIAA ethernet - только Фанук, пробовали старые 16-битовые карты, облом. Может, кому и повезет.

2. Windows 7/32 бита от версии 7.0, 64 бита от версии 8.0

[andrey2147 172]

Спасибо за ответ,посмотрел,а штеккера RJ45 у меня нет.

А ещё вопрос если версия 4.0.0.0 и.файле READMEEN.TXT 

 написано

 

Series 30i, 31i, 32i-MODEL A 
| | Series 16i, 18i, 21i-MODEL B 
| | Power Mate i-D, i-H 
| | Series 0i-MODEL B, 0i-Mate-MODEL B 
| | Series 0i-MODEL C, 0i-Mate-MODEL C 
| | Series 20i-MODEL B 
| | Series 18i-LNB

 

не подойдёт для серии 0iD   ?

[andrey2147 172]

 

2. Windows 7/32 бита от версии 7.0, 64 бита от версии 8.0

Только сейчас понял что имеютя ввиду версии самой проги...

актуальная для 0D версия 9.0...

[bfi 101]

[6] History
==========================================================================

2013/09/02    Edition 9.10
- Improvement of ParameterWindow
 + SERVO HRV+ Control
 + SmartBacklashCompensation
- Improvement of GraphWindow
 + Parameter calculation support function for SmartBacklashCompensation is added.
- Addition of measuring datas
  (Servo:SMTBKL, SMTTRQ, SCREWL, DTRQAL)
- Support Windows 8 (32bit/64bit)

2013/04/12    Edition 9.00
- Addition of Parameter automatic saving function
  and add FileViewer (FileViewer.exe) and Parameter Comparison Tool (PrmCompTool.exe)
- 3-D View Function: 3-D reference path display function is added.
- Tuning Navigator: Spindle velocity gain tuning (for Cs axis) function is added.
- Addition of measuring datas
  (Servo:POSFN,POS3DN, Spindle:CSPOSN,POS3DN,MTPOS, Common power supply:PSPOW)

2012/06/15    Edition 8.40
- In case of using Spindle Tuning Function in the GraphWindow,
  spindle axis except N-th axis in N path can not be selected (N=1-4).
  This problem had been amended. (This problem occurs at Edition 8.30 only)

2012/05/31    Edition 8.30
- Improvement of smoothness compensation for synchronous built-in servo motors
  (Parameter support for 4.5 times/pole-pairs compensation)
- Addition of measuring data for spindle (SPCMD2)
- Improvement of Parameter Window (Spindle synchronous control parameter No.4550-4559).
- Support power source data acquisition at 30i-B series PS
- Add power source data monitoring software "PS Monitor".

2012/03/09    Edition 8.20
- Support of window-collapse of display setting panel for overlay view or 3-D View
- Addition of new operations (Tangent acceleration/jerk, synthetic acceleration/jerk)
- Correction of package file saving for OverlayView Function
- Correction of display content in ParameterWindow (Auto-setting of optimum orientation)

2012/01/31    Edition 8.10
- Addition of overlay view function
  (not supported on 3-D View Function)
- Improvement of 3-D View Function
  + 5-axis coordinate setting : Automatic setting is supported.
  + 5-axis coordinate setting : 5-axis machine parameter setting screen is added.
  + 5-axis coordinate conversion : Imaginary rotary axis is supported.
  + 5-axis coordinate conversion : Angular axis controlled machine is supported.
  + New operations are added. (Curvature, normal acceleration, normal jerk)
  + Length measurement mode is added.
  + 3-D View screen layout switching is supported.
- Tuning Navigator: Improvement of Automatic Backlash Acceleration function
 + Override parameter check screen is added.
- Support 31i/32i/35i-B Transfer Line Function
- Addition of measuring datas (SV:TQMAX,TQMIN,SP:TCMD2)

2011/07/31    Edition 8.00
- Support Power Motion i-MODEL A
- Expansion of the maximum channel number of spindle axis to 4ch. (30i-B Series CNC)
- Addition of tolerance setting of reference data for circular interpolation in ProgramWindow.
- Support Windows 7 (64bit)

2011/01/24    Edition 7.30
- Support Series 30i/31i/32i/35i-MODEL B
- Tool tip hints in ParameterWindow have been revised, and for each parameter
  to be tuned, typical setting value and range of modification are displayed
  as a guideline.
- Graph Window: Fix the TangentN operation problem (7.20 only)

2010/11/17    Edition 7.20
- Improvement of 3-D View Function
  + Display color setting function depending on reference data. (color-coded display)
  + New operations are added. (About path error, rotating radius of 5-axis machining)
  + Addtional functions for ease of operation.
    + Panel for display setting (3-D graph)
    + Rotating operation around axis based on screen (3-D graph)
    + Centering function (3-D graph)
    + Automatic scaling with time axis fixed. (2-D graph)
- Acc./dec. parameters concerning tool center point control are added to the ParameterWindow.
- Add measuring datas for spindle (IRMS,IPEAK,CSPOS2)
- At the 2-D graph in the GraphWindow, the operation that specifies the tool center point
  data (TCP:X,Y,Z) is used and saved to the display settings, an application error occurs
  when opening a new window. It has been amended.

2010/07/13    Edition 7.10
- Frequency response measurement of position loop is supported.
  To use this function, the servo software that supports this function is required.
- In 3-D circle path error display of 3-D View Function, the following problems
  had been amended.
 + When the normal vector of the plane including the reference circle has the
   negative value in the X or Y component, the path error of 3-D circle had
   displayed incorrectly. It has been amended.
 + In case of using the time-range for display, the start data number had been
   ineffective and the waveform was always displayed from the beginning of data.
   It has been amended.

2010/03/31    Edition 7.00
- 3-D View Function (option)
- Support of Windows 7 (32bit) - 64bit version is NOT supported.
- Windows 98/Me/NT4.0 were no longer supported.

2009/11/18    Edition 6.50
- In case of 0i-D, waveform of spindle axis or path-2 servo axes can't be
  measured in the GraphWindow. This problem has been corrected.
  (This problem occurs at Edition 6.40 only)
  The above problem affects the TuningNavigator.

2009/10/16    Edition 6.40
- Graph Window: Improvement of smoothness compensation calculation
- Graph Window: Addition of Automatic saving function
- Graph Window: Addition of Automatic repeat measurement function

2009/06/12    Edition 6.30
- Tuning Navigator: Modification of tuning program for backlash acceleration of rotary axis.
 + A workpiece coordinate system setting G code (G92/G50) was not used in tuning program.
 + Tuning program is generated with incremental command for the axis which accepts
   the incremental command.
 + Tuning program is generated with absolute command for the axis which doesn't accept
   the incremental command (ex. A, B axis on G code system A in the lathe system)

2009/03/30    Edition 6.20
- Tuning Navigator: Addition of gain tuning of Interactive Force Compensation function
- Tuning Navigator: Addition of tuning of unexpected disturbance detection function
- Tuning Navigator: Improvement of Automatic Backlash Acceleration function (Rotary axis supported)
- Parameter Window: Update of servo parameter screens
  + Filter function
   + Resonance elimination filter L
   + Adaptive resonance elimination filter
  + Shape error suppression function
   + Interactive force compensation function (IFC function)
  + Stop function
   + Lifting function against gravity at emergency stop
   + Quick stop function for separate serial detector alarms
  + Unexpected disturbance torque detection function
   + Dynamic friction compensation in the stop state and compensation limit
   + Unexpected disturbance torque detection switching function depending on acceleration
  + Axis setting
   + Acceleration sensor setting

2008/09/10    Edition 6.10
- Synchronous spindle motor screen is added to the ParameterWindow.

2008/05/28    Edition 6.00
- Support Series 0i-MODEL D
- Improvement of Spindle Tuning function
  + Frequency response measurement
  + Tuning Navigator (Automatic tuning for HRV filter)
- Improvement of Tuning Navigator for Automatic Backlash Acceleration function

 

Посмотрите, 0i-MODEL D поддерживается с версии 6.0, но win7/32 от 7.0, вин7/64 от 8.0
 

[andrey2147 172]

Спасибо за ответ, мы купили версию 9.0.завтра начну юзать

Зачем он мне нужен?

Есть одна шлифовка из поднебесной типа обычный токарный станок только вместо резца -шлифовальный круг.

особенность в том что на Х стоит линейка,на мониторе точность-4 нуля после точки

бяка в том что не можем поймать точность на детали железо проверяли наверное, пять раз.есть подозрение на не настроенные привода,хотя error pos прыгает на 1 ед.

Рукой пытаюсь провернуть пару Х она мне  в руку отдаёт толчками,сколько фануков видел такого никогда,привода на 20А.это нормально? не встречалось такого?