Перейти к публикации

Рекомендованные сообщения

i have problem with dnc 80 cybelec

in the upper right corner it says (DPRAM: NO ENC SIGNATURE) and if i press AUTO / AUTO-SEMI / MANUAL.

there notification (ENC NOT CONNECTED) what is problem r and what is the solution

 

https://fil.email/vg60Vi8E

Ссылка на сообщение
Поделиться на других сайтах


However the massage ENC NOT CONNECTED will appear and it will not
be possible to work with the machine.
To reactivate the INTERNAL machine peripheral, you must:
- Select MACHINE INTERNAL.
- Initialize the ENC by pressing INIT ENC, Action menu.

Ссылка на сообщение
Поделиться на других сайтах

thank you for reply
As a result of the delay in a reply from me .A problem has been resolved of  (DPRAM: NO ENC SIGNATURE) 
But I have another problem,after complete indexing,there is no displacement on the upper table when the pedal is pressed

also the key number 3 when i turns to position 3 is not working (I can't change anything).

Ссылка на сообщение
Поделиться на других сайтах
6 часов назад, abdushibi сказал:

A problem has been resolved of  (DPRAM: NO ENC SIGNATURE) 

How was this problem solved?

Ссылка на сообщение
Поделиться на других сайтах

pic1.jpgpic-2.jpgpic-3.jpgpic-4.jpgpic-5.jpgpic-6.jpgI checked the key on the tests page and i found the following

when the key in postion 1 (see pic 1), on the tests page,  is zero see pic 2

 

when the key in postion 2 (see pic 3), on the tests page,  is 2 see pic 4

 

 

when the key in postion 3 (see pic 5 ), on the tests page,  is 2 see pic 6

Ссылка на сообщение
Поделиться на других сайтах

There are 4 wires 0 (common), 1, 2 and 3.

 

1. 0 + 1 = 1 position

2. 0 + 2 = 2 position

3. 0 + 3  and 1 + 2 = 3 position

 

You have no 1 and 3 position.

So I think, that there is the problem with the 1-st wire.

Ссылка на сообщение
Поделиться на других сайтах
41 минуту назад, abdushibi сказал:

In your opinion, what is the solution to this problem?

I think, that you have to dismount the front panel and check the 1-st wire. 

Ссылка на сообщение
Поделиться на других сайтах

i did ,there are four wires As you said i tested with avometer 

are ok  when i turn key to postilion 1  there contact between wire 0 and 1

also   between 0 and 2  also between 0 and 3

i mean also when i turn key to psition  2 there contact between 0 and 2 also when turn  to pisition 3

Ссылка на сообщение
Поделиться на других сайтах
33 минуты назад, abdushibi сказал:

what will be do to solve this problem i need position 3.

You have to use the different connection between the wires to find psition 3.

Ссылка на сообщение
Поделиться на других сайтах

Присоединяйтесь к обсуждению

Вы можете опубликовать сообщение сейчас, а зарегистрироваться позже. Если у вас есть аккаунт, войдите в него для написания от своего имени.
Примечание: вашему сообщению потребуется утверждение модератора, прежде чем оно станет доступным.

Гость
Ответить в тему...

×   Вставлено в виде отформатированного текста.   Вставить в виде обычного текста

  Разрешено не более 75 эмодзи.

×   Ваша ссылка была автоматически встроена.   Отобразить как ссылку

×   Ваш предыдущий контент был восстановлен.   Очистить редактор

×   Вы не можете вставить изображения напрямую. Загрузите или вставьте изображения по ссылке.

  • Сейчас на странице   0 пользователей

    Нет пользователей, просматривающих эту страницу.




×
×
  • Создать...