Перейти к публикации

Вывод описания в шапку программы


Рекомендованные сообщения

Как бы научиться средствами PowerMill выводить в шапку программы описание минимальной и максимальной высот хода фрезы?? 

Ссылка на сообщение
Поделиться на других сайтах


Как бы научиться средствами PowerMill выводить в шапку программы описание минимальной и максимальной высот хода фрезы?? 

Ну как научиться...доки читать надо, посты сочинять, пробовать их)).  

 

 

 

Например в доках есть все, что вам нужно:


 Variable List Continued (3)

Variable Name

Use and Function

LastTool

Last Load Tool number ( Last tool in the series to be used )

LoopCounter

Returns the number of passes in the " repeat " loop function

MaxX ; MaxY ; MaxZ

The overall Maximum limit values of travel for X, Y and Z  

usually used in comments at tape start, or for DUCT block size )

MinX : MinY : MinZ

The overall Minimum limit values of travel for X, Y and Z  

usually used in comments at tape start, or for DUCT block size )

Minutes

Time of Day Minutes

MinorWord

Values from CLdata associated with a particular function ( Rarely used now )

ModelX : ModelY :

ModelZ

Give access to the coordinates in the model system in all circumstances.  These were introduced for a specific operational debug and as such will not normally be of general use

Month

The current month ( numerical  e.g.  04 for April  )

MoveComponentType

This is still under development

MoveMinorType

This is still under development

MoveType

This checks the type of tool path movement ( MoveType = 11 connection moves ; MoveType = 10  5axis moves )  For full list seeWhat’s New

NextAngle

The next angle defined

NextTool

The tool number of the next load tool to be used ( Used for preselection )

NextToolPath

The next tool path to the current one.

NumberPecks

Number of pecks in a drilling cycle

NumberToolPaths

Returns the number of toolpaths in the CLdata file ( used in " repeat " function )

NumberTools

Returns the number of tools in the CLdata file ( used in " repeat " function )

OldX ; OldY ; OldZ ; 

OldAz ; OldEl

The last positional axis move

OptionFileName

This should be used in conjunction with DPversion as a verification that the correct Option has been used to produce the NC output.

OutputWorkPlaneName

The PowerMill NC program Output WorkPlane

PartID

part identification string. This may be obtained from the DUCT PARTNO cldata record, PowerMILL Part Name, the configuration file, or prompted for at run time ( Except prompts are ignored if posted via PowerMILL, or will cause PowerMill to hang )

PartID[ 5 ]

This is similar to above, but has the added flexibility to select the starting point in the Part Identification string via the [ value ].    In the example the 5th character in the Part Name will be the start point, and the number of characters output will be limited by the field width of the carrier word.  ( ID PartID[5] ) 

PeckDepth

Drilling cycle peck depth ( Incremental )

Pitch

Returns the Pitch setting in PowerMill Tap Cycles

Plunging

Check for Plunge move.

Ссылка на сообщение
Поделиться на других сайтах

Т.е. все-таки одним повермилом не обойдешься, нужно постпроцессор править. Понятно. Благодарю

Ссылка на сообщение
Поделиться на других сайтах

Присоединяйтесь к обсуждению

Вы можете опубликовать сообщение сейчас, а зарегистрироваться позже. Если у вас есть аккаунт, войдите в него для написания от своего имени.
Примечание: вашему сообщению потребуется утверждение модератора, прежде чем оно станет доступным.

Гость
Ответить в тему...

×   Вставлено в виде отформатированного текста.   Вставить в виде обычного текста

  Разрешено не более 75 эмодзи.

×   Ваша ссылка была автоматически встроена.   Отобразить как ссылку

×   Ваш предыдущий контент был восстановлен.   Очистить редактор

×   Вы не можете вставить изображения напрямую. Загрузите или вставьте изображения по ссылке.

  • Сейчас на странице   0 пользователей

    Нет пользователей, просматривающих эту страницу.




×
×
  • Создать...