Как найти или содать постпроцессор под АртКам

[Rezhu 0]

Объясните. Есть постпроцессор. Выдернул из Mill 5.0.

В АртКам вставить не получается. Советчики объясняют надо для АртКама писать пост процессор.

Как написать или где взять подскажите

Станок Kin2000, кореец.

Может что то вырезать из текущего и куда вставить.

Вот он какой:

# --------------------------------------------------------------------------

#| MASTERCAM MP POST PROCESSOR | Always back up your post-processor |

#| CNC Software, Inc. | prior to making any changes. It's easy, |

#| Control Model: FAN-0i | just put a floppy in drive a:, at DOS |

#| Machine Model: Kin-2000 | type "COPY C:\NC\*.PST A:" |

#| PST File Name: KINFANINC.PST | |

#| Executable : MP.EXE 3.06 | |

# --------------------------------------------------------------------------

#

# ---------------

#| REVISION LOG |

# ------------------------------------------------------------------------

# Programmers Note:

# CNC 5/20/94 - Initial post setup for Mill5

#$Lgb$

# 1.0 Jph 08/19/94 Initial source control check-in

# 1.1 jph 08/24/94 Correct coolant text

# 1.2 jph 09/02/94 Ques. 86. was 0.2 delay

# 1.3 pdr 09/06/94 Updated and corrected numbered questions

# 1.4 pdr 09/07/94 Updated reverse post name (q 93.)

# 1.5 pdr 09/02/03 Updated reverse

#$Lge$

#

# ---------------

#| FEATURES: |

# ------------------------------------------------------------------------

# Users Note:

#

# Following Misc_Reals & Misc_Integers are used:

#

# mi1 - Work coordinate system

# 0 thru 3 indicate no coordinate information.

# 4 thru 9 = The WCS of G54 thru G59 respectively at each tool.

#

# Options / Usage:

# All toolpaths are started from the initial home to the rapid position.

# It is recommended to start and end cutter compensation on a linear move.

# Rotary axis assumes a "Z" plunge at feed into part, position of the

# substituted axis at absolute zero position and the retraction from path

# by the post call to the G28 machine Z home position.

# --------------------------------------------------------------------------

# DEBUG/PROGRAM SWITCHES, debugging and program switches

# --------------------------------------------------------------------------

bug1 : 1 # 1 = Output post to screen, 2 = output leader to screen

bug2 : 0 # Append postline labels, non-zero is column position?

bug3 : 0 # Append whatline no. to each NC line?

bug4 : 0 # Append NCI line no. to each NC line?

whatno : yes # Do not perform whatline branches?

arcoutput : 1 # 0 = IJK, 1 = R no sign, 2 = R signed neg. over 180

breakarcs : no # Break arcs into quadrants?

stagetool : 0 # 0 = Do not pre-stage tools, 1 = Stage tools

use_gear : no # Set to yes to output gear range codes

# --------------------------------------------------------------------------

# FORMAT STATEMENTS - n=nonmodal, l=leading, t=trailing, i=inc, d=delta

# --------------------------------------------------------------------------

fs 1 0.3i #Decimal, incremental, 4 place

fs 2 0.3d #Decimal, delta

fs 3 1 0 #Integer, not leading

fs 4 2 0l #Integer, two leading

fs 5 3 0l #Integer, three leading

fs 6 4 0l #Integer, four leading

fs 7 0.1 #Decimal, absolute, 1 place

fs 8 0.2 #Decimal, absolute, 2 place

fs 9 0.3i #Decimal, absolute, 3 place

fs 10 0 3t #No decimal, absolute, four trailing

fs 11 0.3t #Decimal, absolute, four trailing

fs 12 0.3 #Decimal, absolute, 4 place

# --------------------------------------------------------------------------

# FORMAT ASSIGNMENTS

# --------------------------------------------------------------------------

# Axis output formats - Linear

# --------------------------------------------------------------------------

fmt X 1 xri # X axis position

fmt Y 1 yri # Y axis position

fmt Z 1 zri # Z axis position

fmt X 1 xr # X rapid position from tool change

fmt Y 1 yr # Y rapid position from tool change

fmt Z 1 zr # Z rapid position from tool change

fmt X 12 xr # X rapid position from tool change

fmt Y 12 yr # Y rapid position from tool change

fmt Z 12 zr # Z rapid position from tool change

fmt X 12 xh # X home position

fmt Y 12 yh # Y home position

fmt Z 12 zh # Z home position

# --------------------------------------------------------------------------

# Axis output formats - Circular

# --------------------------------------------------------------------------

fmt I 2 i # Arc center description in X

fmt J 2 j # Arc center description in Y

fmt K 2 k # Arc center description in Z

fmt R 2 arcrad # Arc Radius

fmt R- 1 arcradm # Arc Radius over 180 degree sweep

# --------------------------------------------------------------------------

# Axis output formats - Rotary substitution

# --------------------------------------------------------------------------

fmt A 9 xangle # Linear to rotary calculation of X

fmt B 9 yangle # Linear to rotary calculation of Y

# --------------------------------------------------------------------------

# Program & Sequence number format

# --------------------------------------------------------------------------

fmt O 6 progno # Program number

fmt N 3 n # Sequence nos.

# --------------------------------------------------------------------------

# Tool format

# --------------------------------------------------------------------------

fmt T 3 t # Tool No

fmt T 3 first_tool# First Tool Used (bldnxtool: yes)

fmt T 3 next_tool # Next Tool Used (bldnxtool: yes)

fmt D 3 tloffno # Diameter Offset No

fmt H 3 tlngno # Length Offset No

fmt "TOOL - " 4 tnote # Note format

fmt "DIA. OFF. - " 4 toffnote # Note format

fmt "LENGTH - " 4 tlngnote # Note format

fmt "DIA. - " 11 tldia # Note format

# --------------------------------------------------------------------------

# Spindle Speeds & Feedrate output formats

# --------------------------------------------------------------------------

fmt S 6 speed # Spindle Speed

fmt F 8 fr # Feedrate

fmt F 7 frdeg # Feedrate for rotary

fmt M 3 gear # Gear range

# --------------------------------------------------------------------------

# Drill variable formats

# --------------------------------------------------------------------------

fmt G 3 drillref # Initial / Reference Toggle (G98/G99)

fmt P 10 dwell # Dwell

fmt Z 12 initht # Initial Height

fmt R 12 refht # Reference Height

fmt R 12 refout # Reference Height out

fmt Z 12 depth # Depth

fmt Z 12 depthout # Depth out

fmt Q 10 peck1 # First peck increment (positive)

fmt 12 peck2 # Second or last peck (positive)

fmt 12 peckclr # Safety distance

fmt 12 retr # Retract height

fmt F 8 frplunge # Plunge feedrate in drill cycles

# --------------------------------------------------------------------------

# Miscellaneous output formats

# --------------------------------------------------------------------------

fmt M 5 ssrange # Spindle Speed Range

fmt C 4 coolant # Coolant

# --------------------------------------------------------------------------

# INITIALIZE - initialize system variables and define user variables

# --------------------------------------------------------------------------

qtoolpln : no # MP386 - Enable tool plane option

qtoolopt : no # MP386 - Enable tool optimization

arctype : 4 # Arc center 1=abs, 2=St-Ctr, 3=Ctr-St, 4=unsigned inc.

bldnxtool : yes # Build next tool table

ldrcode : 65 # Leader character dec. equiv. (fleader outputs code)

ncldr : 20 # No. of leader characters (fleader outputs code)

nobrk : no # Omit breakup of x/y & z rapid moves

omitcrlf : no # Omit CR/LF

omitrefht : no # Don't use reference height on first non-canned Z move

omitseq : no # Omit sequence no.

omitz : no # Omit first Z movement for non-canned-cycles

progname : 1 # Use uppercase for program name

scalex : 1.0 # Scaling of .NCI at input - x,y,z,i,j,k

scaley : 1.0 # Scaling of .NCI at input - x,y,z,i,j,k

scalez : 1.0 # Scaling of .NCI at input - x,y,z,i,j,k

seqmax : 9999 # Max. sequence no.

skipmotest: no # Skip motion test in linear

spaces : 1 # No. of spaces to add between fields

tooltable : 1 # Read for tool table and pwrtt

absswp : 0 # Absolute sweep

drlgsel : -1 # Drill Select Initialize

maxfrdeg : 999 # Limit for feed in deg/min

absinc : 0 # Absolute/Incremental toggle for modality

tcnt : 0 # Count the number of tool changes

adelta : 0 # Calculation for deg/min

ldelta : 0 # Calculation for deg/min

zdelta : 0 # Calculation for deg/min

alzdelta : 0 # Calculation for deg/min

frdelta : 0 # Calculation for deg/min

frdegcalc : 0 # Calculation for deg/min

circum : 0 # Calculation for deg/min

rotstrt : 1 # Flag for first rotary position

# --------------------------------------------------------------------------

# FORMULAS - global formulas

# --------------------------------------------------------------------------

ssrange = mi3 # Gear Range Select

speed = abs ( ss ) # Absolute spindle speed

arcradm = arcrad # Negative arcrad

spdlsel = fsg3(ss) # Spindle on selector based on pos. or neg. ss

xri = xr # Apply value for inc. output

yri = yr # Apply value for inc. output

zri = zr # Apply value for inc. output

# --------------------------------------------------------------------------

# CANNED CYCLES - select long or short code

# --------------------------------------------------------------------------

usecandrill : yes # Use canned cycle for drill

usecanpeck : yes # Use canned cycle for Peck

usecanchip : yes # Use canned cycle for Chip Break

usecantap : yes # Use canned cycle for Tap

usecanbore1 : yes # Use canned cycle for Bore1

usecanbore2 : yes # Use canned cycle for Bore2

usecanmisc1 : yes # Use canned cycle for Misc1

usecanmisc2 : yes # Use canned cycle for Misc2

# --------------------------------------------------------------------------

# Lookup table definitions - for math functions FLOOK and FRANGE

# --------------------------------------------------------------------------

flktbl 1 3 # Lookup table definitions - table no. - no. entries

40 1000 # Low gear range

41 2500 # Med gear range

42 5000 # Hi gear range

# --------------------------------------------------------------------------

# Strings - String labels must start with 's' - they are not pre-assigned

# --------------------------------------------------------------------------

#Select operation note

sop00 NULL # String definition

sop01 2D-CONTOUR # " "

sop02 3D-CONTOUR # " "

sop03 DRILL/MISC # " "

sop04 POCKET.... # " "

sop05 RULED..... # " "

sop06 2D-SWEPT.. # " "

sop07 3D-SWEPT.. # " "

sop08 REVOLVED.. # " "

sop09 LOFT...... # " "

sop10 COONS..... # " "

sop11 TRIM ..... # " "

sop12 FILLET.... # " "

sop13 ROUGH..... # " "

sop14 OP14...... # " "

sop15 OP15...... # " "

sopnote # Target string

fstrsel sop00 opcode sopnote

# --------------------------------------------------------------------------

# Select motion G code

sg00 G00 # Linear movement at rapid feedrate

sg01 G01 # Linear movement at feedrate

sg02 G02 # Circular interpolation CW

sg03 G03 # Circular interpolation CCW

sgcode # Target string

fstrsel sg00 gcode sgcode

# --------------------------------------------------------------------------

# Select incremental or absolute G code

sg90 G90 # Absolute G code

sg91 G91 # Incremental G code

sgabsinc # Target string

fstrsel sg90 absinc sgabsinc

# --------------------------------------------------------------------------

# Select spindle start

sm04 M4 # Spindle reverse

sm05 M5 # Spindle off

sm03 M3 # Spindle forward

spdlon # Target string

fstrsel sm04 spdlsel spdlon

# --------------------------------------------------------------------------

# Cutter compensation code

scc0 "" # Cutter compensation state not changed

sg40 G40 # Cancel cutter compensation

sg41 G41 # Cutter compensation left

sg42 G42 # Cutter compensation right

sg140 G40 # Last linear move cancel cutter comp (see note)

# Note: to cancel comp after last move, remove G40 string

# with sg140 and remove "#" at the postline call "pcancelcc"

sccomp # Target string

fstrsel scc0 ccomp sccomp

# --------------------------------------------------------------------------

# Select work plane G code

sg17 G17 # XY plane code

sg19 G19 # XZ plane code

sg18 G18 # YZ plane code

sgplane # Target string

fstrsel sg17 plane sgplane

# --------------------------------------------------------------------------

# Work coordinate system

sg50 "" # Work coordinate system G code

sg51 "" # " " " " "

sg52 "" # " " " " "

sg53 "" # " " " " "

sg54 G54 # " " " " "

sg55 G55 # " " " " "

sg56 G56 # " " " " "

sg57 G57 # " " " " "

sg58 G58 # " " " " "

sg59 G59 # " " " " "

sgwcs # Target string

fstrsel sg50 mi1 sgwcs

# --------------------------------------------------------------------------

# Canned drill cycle string select

sg81 G81 # drill - no dwell

sg81d G82 # drill - with dwell

sg83 G83 # peck drill - no dwell

sg83d G83 # peck drill - with dwell

sg73 G73 # chip break - no dwell

sg73d G73 # chip break - with dwell

sg84 G84 # tap - no dwell

sg84d G74 # tap - with dwell (selects left hand)

sg85 G85 # bore #1 - no dwell

sg85d G89 # bore #1 - with dwell

sg86 G86 # bore #2 - no dwell

sg86d G86 # bore #2 - with dwell

sgm1 G81 # misc #1 - no dwell

sgm1d G82 # misc #1 - with dwell

sgm2 G81 # misc #2 - no dwell

sgm2d G82 # misc #2 - with dwell

sgdrill # Target string

drlgsel = drillcyc * 2 + fsg2 ( dwell ) # 16 possible combinations:

# drillcyc = 0..7

# dwell = 0 or non-zero (2 states)

fstrsel sg81 drlgsel sgdrill

# --------------------------------------------------------------------------

# Generate 'sgear' string

sgear0 M** # auto gear range

sgear1 M41 # Low gear range

sgear2 M42 # Med gear range

sgear3 M43 # High gear range - selected in parameters by mi3

sgear

fstrsel sgear0 gear sgear

# --------------------------------------------------------------------------

# POSTLINES, USER-DEFINED - Postline labels start with 'p'.

# End a line with ',' to continue on the next line.

# End a line with ', e' to generate carriage return and linefeed.

# --------------------------------------------------------------------------

# Program general output control, user defined

# --------------------------------------------------------------------------

pinit # Initialize Vars

prv_xri = xh

prv_yri = yh

prv_zri = zh

prv_fr = 999.999

prv_frdeg = 999.999

prv_frplunge = 999.999

linarc = 0

rotstrt = 1

pcomment # Manual Entry - COMMENTS (on a block by itself) 1005,1006

"(", scomm, ")"

pabs # Absolute G code output

absinc = 0

sgabsinc

pinc # Incremental G code output

absinc = 1

sgabsinc

pcooloff # Coolant off "M" code output

if prv_coolant > 0, "M09"

pcoolon # Coolant off "M" code output

if coolant = 1, "M08" # Flood

if coolant = 2, "M08" # Mist

pcoolnl # Coolant off "M" code output

if coolant = 0, "M09" # Off

if coolant = 1, "M08" # Flood

if coolant = 2, "M08" # Mist

pfr # Feedrate W/O Negative Feedrates

if fr > 0, fr

pcan # Canned text - cantext = 0, 1, 2, 3

if cantext = 1, "M01" #optional stop

if cantext = 2, " " #user option

if cantext = 3, " " #user option

# --------------------------------------------------------------------------

# Work coordinate output, user defined

# --------------------------------------------------------------------------

pg92_sof # G92 coordinate setting at start

pinc, "G28", "Z0.", "V0.", e

"G28", "X0.", "Y0.", e

pg92_out # G92 coordinate setting at tool change

"G28", "X0.", "Y0.", e

if gcode <> 1003, *sgwcs, *xh, *yh, *zh, e

pg92_tst # G92 coordinate test for output

if mi1 > 0, pg92_out

pwcs # G54+ coordinate setting

if mi1 >= 4, *sgwcs

# --------------------------------------------------------------------------

# Gear selection control, user defined

# --------------------------------------------------------------------------

pgear # Find spindle range

gear = frange ( 1, speed )

*gear

prange # Find spindle range

if use_gear = 1, pgear

# --------------------------------------------------------------------------

# Cutter comp. output control, user defined

# --------------------------------------------------------------------------

pccdia2 # Cutter Compensation2

if ccomp <> 4, tloffno

pccdia # Cutter Compensation

if ccomp <> 0, pccdia2

# --------------------------------------------------------------------------

# Axis substitution motion, user defined

# --------------------------------------------------------------------------

pdrlxyrot # Substitute Axis X/Y with Rotary axis w/ drilling

xangle = xs

yangle = ys

if rotaxis = 0, x, y

if rotaxis = 1, y, xangle

if rotaxis = 2, x, yangle

pfrd # Feedrate W/O Negative Feedrates (deg/min)

if frdeg > maxfrdeg, frdeg = maxfrdeg

if frdelta > .5, *frdeg #Value to exceed to output frdeg

protaxis1a # Substitute Axis X/Y with Rotary axis

if rotstrt = 0, sgcode, y, z, *xangle, pfrd, pcan, e

if rotstrt = 1, xangle, e

if rotstrt = 1, sgcode, y, z, pfrd, pcan, e

protaxis1 # Substitute Axis X/Y with Rotary axis

if gcode = 0, sgcode, y, z, *xangle, pcan, e

if gcode = 1, protaxis1a

protaxis2a # Substitute Axis X/Y with Rotary axis

if rotstrt = 0, sgcode, x, z, *yangle, pfrd, pcan, e

if rotstrt = 1, yangle, e

if rotstrt = 1, sgcode, x, z, pfrd, pcan, e

protaxis2 # Substitute Axis X/Y with Rotary axis

if gcode = 0, sgcode, x, z, *yangle, pcan, e

if gcode = 1, protaxis2a

protaxis # Substitute Axis X/Y with Rotary axis

xangle = xs

yangle = ys

if rotstrt = 1, !fr

if fr < 0, fr = prv_fr

!fr

if rotaxis = 1, ldelta = abs ( y - prv_y )

if rotaxis = 2, ldelta = abs ( x - prv_x )

zdelta = abs ( z - prv_z )

if rotaxis = 1, adelta = ( ( abs ( xangle - prv_xangle ) ) / 360 ) * circum

if rotaxis = 2, adelta = ( ( abs ( yangle - prv_yangle ) ) / 360 ) * circum

alzdelta = sqrt ( adelta^2 + ldelta ^2 + zdelta^2 )

frdegcalc = fr * ( 360 / circum )

if alzdelta <> 0, frdeg = ( adelta / alzdelta ) * frdegcalc

if adelta = 0, frdeg = fr

frdelta = abs ( frdeg - prv_frdeg )

if rotaxis = 1, protaxis1

if rotaxis = 2, protaxis2

if gcode = 1, rotstrt = 0

!x, !y, !z

protary # Rotary Move

if rotaxis = 1, xr = 0 #Force X to zero

if rotaxis = 2, yr = 0 #Force Y to zero

if rotaxis > 0, linarc = 1

circum = rotdia * pi

# --------------------------------------------------------------------------

# Axis linear/circular motion, user defined

# --------------------------------------------------------------------------

parctyp2 # Arc output for R w/ sign over 180 degree sweep

absswp = abs ( sweep )

if absswp <= 180,*arcrad

if absswp > 180, *arcradm

parctyp1 # Arc output for R w/ no sign

*arcrad

parctyp0 # Arc output for IJK

if plane = 0, *i, *j, k

if plane = 1, i, *j, *k

if plane = 2, *i, j, *k

parctyp # Select the arc output

if arcoutput = 0, parctyp0

if arcoutput = 1, parctyp1

if arcoutput = 2, parctyp2

prapidm # Linear line movement - at rapid feedrate

sgplane, sccomp, pccdia, sgcode, x, y, z, pcan

plinm # Linear line movement - at feedrate

sccomp, pccdia, sgcode, x, y, z, pfr, pcan

pcirm # Circular interpolation

sgplane, sccomp, pccdia, sgcode, x, y, z, parctyp, pfr, pcan

# --------------------------------------------------------------------------

# Drilling, user defined

# --------------------------------------------------------------------------

pdrillclc # Determine depth and reference

depthout = depth - refht

refout = refht - zr

pdrillref # Determine G98 or G99

if initht <> refht, drillref = 98

if initht = refht, drillref = 99

pdwell # Determine whether to output dwell

if dwell <> 0, *dwell

ptlchg0dr3 # Null tool change for drilling

gcode = 0

if zr < prv_zr, sgcode, *xri, *yri, e

sgcode, *zri, e

ptlchg0dr2 # Null tool change for drilling

if zr <> prv_zr, ptlchg0dr3

ptlchg0drl # Null tool change for drilling

if prv_opcode = 3, ptlchg0dr2

# --------------------------------------------------------------------------

# POSTLINES, PRE-DEFINED - Postline names are pre-assigned.

# Lines do not need to end with ', e' for carriage return and linefeed.

# --------------------------------------------------------------------------

pheader # File header

"(PROGRAM NAME -", progname, ")"

"(DATE, Day-Month-Year - ", date, " TIME, Hr:Min - ", time, ")"

psof0 # Start of file for tool zero

psof

psof # Start of file for non-zero tool number

pinit

!opcode, !coolant

if tcnt = 1, stagetool = 2

" ", e

"%"

progno

comment

"G91", "G28", "Z0."

"G91", "G28", "X0.", "Y0."

"G17 G40 G49 G90"

"G92", "X0.", "Y0.", "Z0."

"M00"

"M06"

if stagetool = 0,"M91", *t

"M14"

protary

"G00", "G55", "G90", "X0.", "Y0."

"G43", tlngno, *zr, pcoolon

"G04X4."

"G17 G61 G91"

"G10.3"

x = xri

y = yri

!x, !y

ptlchg0 # Null tool change

if opcode = 3, ptlchg0drl

if prv_speed <> speed, speed

if coolant <> prv_coolant, pcoolnl

!opcode, !zr, !coolant

ptlchg # Tool change

pinit

!opcode

"M15"

"G04X8."

"G91", "G28", "Z0."

if stagetool = 0, "M91", *t

comment

protary

"G00", "G90","X0.", "Y0."

"G43", tlngno, *zr, pcoolon

"M14"

"G04X4."

"G17 G61 G91"

x = xri

y = yri

!x, !y

!coolant

peof0 # End of file for tool zero

peof

peof # End of file for non-zero tool

"M15"

"G91", "G28", "Z0."

"/", "M07"

"G91", "G28", "X0.", "Y0."

"M30"

"%"

# --------------------------------------------------------------------------

# Axis motion

# --------------------------------------------------------------------------

prot0 # Toolplane postline - Custom post required

prot # Toolplane postline - Custom post required

prapid # Linear line movement - at rapid feedrate

if rotaxis <> 0, protaxis

if rotaxis = 0, prapidm

pzrapid # Linear movement in Z axis only - at rapid feedrate

sgcode, z

plin1 # First linear movement after SOF, whatno must be set

plin2 # Second linear movement after SOF, whatno must be set

plin # Linear line movement - at feedrate

if rotaxis <> 0, protaxis

if rotaxis = 0, plinm

pz # Linear movement in Z axis only - at feedrate

sgcode, z, pfr

pcir1 # First circular movement after SOF, whatno must be set

pcir2 # Second circular movement after SOF, whatno must be set

pcir # Circular interpolation

if rotaxis <> 0, protaxis

if rotaxis = 0, pcirm

# --------------------------------------------------------------------------

# Drilling

# --------------------------------------------------------------------------

pdrill # Canned Drill Cycle

pdrillref

n, *drillref, *sgdrill, pdrlxyrot, *depth, *refht, pdwell, *frplunge

ppeck # Canned Peck Drill Cycle

pdrillref

n, *drillref, *sgdrill, pdrlxyrot, *depth, *refht, *peck1, *frplunge

pchpbrk # Canned Chip Break Cycle

pdrillref

n, *drillref, *sgdrill, pdrlxyrot, *depth, *refht, *peck1, *frplunge

ptap # Canned Tap Cycle

pdrillref

n, *drillref, *sgdrill, pdrlxyrot, *depth, *refht, *frplunge

pbore1 # Canned Bore #1 Cycle

pdrillref

n, *drillref, *sgdrill, pdrlxyrot, *depth, *refht, pdwell, *frplunge

pbore2 # Canned Bore #2 Cycle

pdrillref

n, *drillref, *sgdrill, pdrlxyrot, *depth, *refht, *frplunge

pmisc1 # Canned Misc #1 Cycle (User Option)

pdrill

pmisc2 # Canned Misc #2 Cycle (User Option)

pdrill

pdrill_2 # Canned Drill Cycle

n, pdrlxyrot, refht, depth

ppeck_2 # Canned Peck Drill Cycle

pdrill_2

pchpbrk_2 # Canned Chip Break Cycle

pdrill_2

ptap_2 # Canned Tap Cycle

pdrill_2

pbore1_2 # Canned Bore #1 Cycle

pdrill_2

pbore2_2 # Canned Bore #2 Cycle

pdrill_2

pmisc1_2 # Canned Misc #1 Cycle

pdrill_2

pmisc2_2 # Canned Misc #2 Cycle

pdrill_2

pcanceldc # Cancel canned drill cycle

!gcode

n, "G80"

pcancelcc # Cancel cutter comp.

#n, "G40"

pwrtt # Write tool table, scans entire file, null tools are negative

tnote = t

toffnote = tloffno

tlngnote = tlngno

if t >= 0, "(", *tnote, " ", *toffnote, " ", *tlngnote, " ", *tldia, " ",

*sopnote, ")"

if t >= 0, tcnt = tcnt + 1

# --------------------------------------------------------------------------

# Numbered questions for Mastercam -- Used by Mill 5

# --------------------------------------------------------------------------

38. Rapid feedrate? 300.0

76. Startup configuration file? MILL5

80. Communications port number for receive and transmit (1 or 2) ? 2

81. Data rate (110,150,300,600,1200,2400,4800,9600,14400,19200,38400)? 300

82. Parity (E/O/N)? E

83. Data bits (7 or 8)? 7

84. Stop bits (1 or 2)? 2

85. Strip line feeds? N

86. Delay after end of line (seconds)? 0

87. Ascii, Eia, or Binary (A/E/B)? A

88. Echo keyboard to screen in terminal emulation? n

89. Strip carriage returns? N

90. Drive and subdirectory for NC and Material files?

91. Name of executable post processor? MP

92. Name of reverse post processor? RP

93. Reverse post PST file name? RPINC

100. Number of places BEFORE the decimal point for sequence numbers? 3

101. Number of places AFTER the decimal point for sequence numbers? 0

103. Maximum spindle speed? 5000

107. Average time for tool change (seconds)? 2.0

110. Default tool library? TOOLS.MTL

# --------------------------------------------------------------------------

# Default Miscellaneous Real Values

# --------------------------------------------------------------------------

201. Default miscellaneous real variable 1 (mr1)? 0.0

202. Default miscellaneous real variable 2 (mr2)? 0.0

203. Default miscellaneous real variable 3 (mr3)? 0.0

204. Default miscellaneous real variable 4 (mr4)? 0.0

205. Default miscellaneous real variable 5 (mr5)? 0.0

206. Default miscellaneous real variable 6 (mr6)? 0.0

207. Default miscellaneous real variable 7 (mr7)? 0.0

208. Default miscellaneous real variable 8 (mr8)? 0.0

209. Default miscellaneous real variable 9 (mr9)? 0.0

210. Default miscellaneous real variable 10 (mr10)? 0.0

# --------------------------------------------------------------------------

# Default Miscellaneous Integer Values

# --------------------------------------------------------------------------

301. Default Work Coordinate System (0 thru 3=G92, 4 thru 9=G54-G59)? 1

302. Miscellaneous integer variable 2 (mi4)? 0

303. Miscellaneous integer variable 3 (mi4)? 0

304. Miscellaneous integer variable 4 (mi4)? 0

305. Miscellaneous integer variable 5 (mi5)? 0

306. Miscellaneous integer variable 6 (mi6)? 0

307. Miscellaneous integer variable 7 (mi7)? 0

308. Miscellaneous integer variable 8 (mi8)? 0

309. Miscellaneous integer variable 9 (mi9)? 0

310. Miscellaneous integer variable 10 (mi10)? 0

Изменено 1 сентября 2011 пользователем Rezhu